Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a "controlled document". Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2000 Elantec Semiconductor, Inc.
EL
6283C -
Produ
c
t
B
r
ief
Features
· Shrink-Small Outline Package
· Voltage-controlled output current
source to 200mA per channel,
requiring one external set resistor
per channel
· Current-controlled output current
source to 200mA per channel
· Rise time = 0.8ns
· Fall time = 0.8ns
· On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
· Oscillator to 500MHz
· Oscillator to 100mA pk/pk
· Single +5V supply (±10%)
· Disable feature for power-up
protection and power savings
· Fast Settling APC Amplifier
Applications
· CD-RW applications
· Writable optical drives
· Laser diode current switching
Ordering Information
Part No
Temp. Range
Package
Outline #
EL6283CU
0°C to +70°C
QSOP-16
MDP0041
General Description
The EL6283C is a high-performance three channel laser driver that
provides controlled current to a grounded laser diode. Write channels
2 and 3 can provide up to 200mA per channel of DC or pulsed current,
with switching speeds of approximately one nanosecond rise/fall time.
All three channels are summed together at the I
OUT
output, allowing
the user to create multilevel waveforms in order to optimize laser
diode performance. The level of the output current is set by an analog
voltage applied to an external resistor which converts the voltage into
a current at the I
IN
pin (virtually ground). The current seen at this pin
is then amplified to become a current source at pin I
OUT
.
An on-chip 500MHz oscillator is provided to allow output current
modulation when in any mode. This is turned on when the OSCEN pin
is held high. Complete control of amplitude and frequency is set by
two external resistors connected to ground at pins RFREQ and RAMP
(see graphs in this data sheet for further explanation).
Output current pulses are enabled when an `L' signal is applied to the
OUTEN pin. No output current flows when OUTEN is `H', and addi-
tional laser diode protection is provided since the OUTEN input will
float high when open. Complete I
OUT
shut-off is also achieved by
holding the ENABLE pin low, which will override all other control
pins.
The EL6283C also includes a fast settling APC amplifier designed to
interface directly with the front end monitor diode and the sample-
and-hold amplifier for read and write power control. Its 100MHz
bandwidth and 30ns settling time enable up to 16X CD-RW design.
Connection Diagram
1
2
3
4
16
15
14
13
5
6
7
12
11
10
8
9
VREF
VCC
IINR
IOUT
RFREQ
GND
IIN2
ENABLE
IIN3
RAMP
OUTEN3
OSCEN
OUTEN2
VCC
VOUT
PDIN
EL6283C - Product Brief
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
S
e
pte
m
ber 28, 2000
2
EL6283C - Product Brief
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
EL628
3C
- Produ
c
t
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.'s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
other consequential damages.
S
e
p
t
ember
28, 2000
Printed in U.S.A.
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
Fax:
(408) 945-9305
European Office: +44-118-977-6080
Japan Technical Center: +81-45-682-5820
PDF 
ZIP