Du line
®
Fieldbus
Installationbus
Specifications are subject to change without notice (29.04.03)
1
Dupline
®
is a registered trademark. A product of the CARLO GAVAZZI Group
· 8 NPN- or PNP-transistor outputs
for control of floor-indicators
· Open printed circuit board
· Bracket for DIN-rail mounting available
· LED-indications for supply and Dupline
®
carrier
· 3-wire system with Dupline
®
and DC-supply through
G 2196 0000 700
· Channel coding by GAP 1605
Product Description
Ordering Key
Module with 8 NPN- or PNP-
transistor outputs for direct
interface to elevator floor
indicators. The 8 outputs can
either be connected to the 8
inputs of intelligent floor indi-
cators which are controlled
by bit-combinations or they
can be used to drive LED-
segments directly. All modules
in an elevator is connected to
the same 3 wires for bus-
communication with the con-
trol system and DC-power-
supply for the lamps/LED's.
Installer friendly mounting,
operation and maintenance
without requirement of any
special tools or programm-
ing.
Type: Dupline
®
Open PCB
Output-Module
Number of I/Os
Output type
DC-supply
Type Selection
Supply
Ordering no.
Ordering no.
NPN-outputs
PNP-outputs
10-30 VDC
G 2130 5511 700
G 2130 5521 700
G 2130 5521 700
Output Specifications
Supply Specifications
Output-Module for Elevators
Outputs
8 PNP-transistors
Output voltage drop
2.0 V
Current per output
100 mA
Total load capability (01..08)
500 mA
Reverse polarity protection
Yes
Short-circuit protection
None
Built-in protective diodes
Yes
Off-state leakage current
200 µA
Response time
1 pulse train
(136 ms @ 128 channels)
Power supply
Overvoltage cat. III (IEC 60664)
Rated operational voltage (V
in
) 10-30 VDC (ripple included)
Ripple
3 V
Reverse polarity protection
Yes
Current consumption
45 mA
Power dissipation
1 W
Inrush current
1 A
Transient protection voltage
800 V
Dielectric voltage
Supply - Dupline
®
None
Supply - Outputs
None
Type G 2130 55.1 700
General Specifications
Power ON delay
Typ. 2 s
Indication for
Supply ON
LED, green
Dupline
®
carrier
LED, yellow
Environment
Operating temperature
-20 to +50°C (-4 to +122°F)
Storage temperature
-50 to +85°C (-58 to +185°F)
Humidity (non-condensing)
20 - 80%
Mechanical resistance
Shock
15 G (11 ms)
Vibration
2 G (6 to 55 Hz)
Dimensions
Open PCB 74 x 59 mm
4 pcs. of nylon PA6 snap
locks are included for mount-
ing the PCB in ø 4.8 holes
Weight
50 g
Du line
®
Fieldbus
Installationbus
2
Specifications are subject to change without notice (28.09.99)
Dupline
®
is a registered trademark. A product of the CARLO GAVAZZI Group
Mode of Operation
The output unit uses three
wires for the communication
with all the other I/O-units of
an installation, for the sup-
ply of the I/O-units and for
the loads connected to the
outputs of the units. This
implies, that the "common"
of the communication signal
is identical to the "minus" of
the supply.
The DC supply voltage must
connect to the system
through a G 2196 0000 700,
which also performs the
channel generator function
and the RS485 communica-
tion link to the elevator con-
troller (please refer to the
data sheet for G2196 0000
700 for details).
8 out of the 128 available
Dupline
®
adresses should be
reserved to control the floor-
indicators. Since all the indic-
ators must show the same
value, the output modules
can all be coded to read the
same adresses. This implies
that only 8 adresses will be
occupied for floor indication
no matter how many indic-
ators are installed.
The output status of all out-
puts of an output unit may
be predefined for cases like
loss of power and loss of
communication. Please refer
to the paragraph "Output
status setting" of the data
sheet for the GAP 1605 to
change the default setting
(all outputs OFF).
Pin Allocation
Terminal
DUP
GND
POW
DC +
O 1
O 2
O 3
O 4
O 5
O 6
O 7
O 8
Dup (Dupline
®
S)
GND
DC +
O1
O2
O3
O4
O5
O6
O7
O8
POW (Supply input)
Input/Output
Dupline
®
signal
Dupline
®
+ supply GND
Supply IN
DC for output loads
Output 1
Output 2
Output 3
Output 4
Output 5
Output 6
Output 7
Output 8
Wiring Diagrams
G 2130 55.1 700
Accessories
Aluminium bracket for
DIN-mounting
8047- bracket
DIN-rail
FMD 411
Channel
pr
ogram
plug
Supply
LIne
Dup (Dupline
®
S)
GND
DC +
O1
O2
O3
O4
O5
O6
O7
O8
POW (Supply input)
Channel
pr
ogram
plug
Supply
LIne
G 21305511...
G 21305521...
PDF 
ZIP