2436
COUNTDOWN POWER TIMER
DISCONTINUED PRODUCT
-- FOR REFERENCE ONL
Y
Dwg. No. PS-016
The ULQ2436M is a rugged, long-duration countdown timer
specifically designed to operate in an automotive or industrial environ-
ment. It uses an internal RC oscillator to drive a digital countdown
circuit for timing periods of typically 2-1/2 to 5 minutes. The
ULQ2436M multiplies the oscillator period by 4064. Internal logic can
automatically cause the timeout to be halved for successive timeouts.
I
2
L technology is used for the countdown and logic circuitry and
conventional linear bipolar devices for the oscillator and output power
functions. This combination, together with the low-cost 8-pin mini-DIP
plastic package, results in a very economical power timer suitable for a
wide variety of applications.
The Darlington-connected output driver is capable of switching
loads up to 400 mA.
FEATURES
s
28 V/400 mA Output Switch
s
Low-Cost Ceramic Timing Capacitor
s
Dual-Mode Timing Operation
s
-40
°
C to +85
°
C Operation
s
10 V to 16 V Operation
s
Internal Stabilizing Regulator
s
Low-Cost 8-Pin Mini-DIP
2436
1
2
3
4
5
6
7
8
TOGGLE
GROUND
OUTPUT
OSC.
SUPPLY
MODE SELECT
NO
CONNECTION
NO
CONNECTION
VREG
COUNTER
F/F
Always order by complete part number:
ULQ2436M .
Dwg. No. PS-016
COUNTDOWN POWER TIMER
Data Sheet
27462.20A
APPLICATIONS
s
Automotive Rear-Window Defogger Timer
s
Automotive Courtesy Light Timer
s
Appliance Power Timer
s
Power Control System
ABSOLUTE MAXIMUM RATINGS
at T
A
= +25
°
C
Supply Current, I
REG
. . . . . . . . . . . . 15 mA
Output Voltage, V
OUT
. . . . . . . . . . . . . 28 V
Output Current, I
OUT
. . . . . . . . . . . 400 mA
Input Voltage, V
1
or V
4
(2 min.) . . . . . 24 V
(continuous) . . . . . . . . . . . . . . . . . 16 V
Package Power Dissipation,
P
D
. . . . . . . . . . . . . . . . . . . . See Graph
Operating Temperature Range,
T
A
. . . . . . . . . . . . . . . . -40
°
C to +85
°
C
Storage Temperature Range,
T
S
. . . . . . . . . . . . . . . -65
°
C to +150
°
C
2436
COUNTDOWN POWER TIMER
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
ELECTRICAL SPECIFICATIONS at T
A
= -40
°
C to +85
°
C, V
CC
= 12 V
(unless otherwise specified).
Limits
Characteristic
Test Conditions
Min.
Max.
Units
Regulator Voltage
I
REG
= 12 mA, Output Off
7.0
9.0
V
Output Saturation Voltage
I
OUT
= 400 mA, T
A
= +25
°
C
--
2.5
V
I
OUT
= 250 mA, T
A
= +25
°
C
--
1.35
V
Output Leakage Current
V
OUT
= 28 V, V
CC
= 12 V
--
100
µ
A
V
OUT
= 22 V, V
CC
= Open Circuit
--
100
µ
A
Input Threshold Voltage
10 k
Series Resistor
1.0
5.0
V
Oscillator Tolerance
T
A
= +25
°
C
--
±
3.0
%
T
A
= -40
°
C to +85
°
C
--
±
6.0
%
Initial Timeout
4064
4064
--
Subsequent Timeouts
2032
2032
--
Divider Count
(V
CC
= 10 V to 16 V)
Dwg. ES-012A
TEST CIRCUIT AND TYPICAL
REAR-WINDOW DEFOGGER APPLICATION
C
0.1
µ
F
T
R 1 k
S
C
S
65
, 65 mH
+
1
2
3
4
5
6
7
8
VREG
COUNTER
F/F
V
CC
10 k
24 V
1
µ
F
TOGGLE
R
1.5 M
T
10 k
Dwg. GP-009-1B
50
75
100
125
150
0.5
0
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
TEMPERATURE IN
°
C
2.0
1.5
1.0
25
R = 55
°
C/W
JC
FREE AIR, R = 80
°
C/W
JA
W
Copyright © 1987, 1993, Allegro MicroSystems, Inc.
2436
COUNTDOWN POWER TIMER
1 k
+
1
µ
F
1
2
3
4
5
6
7
8
VREG
COUNTER
F/F
BATTERY
10 k
16 V
TO
COURTESY
LIGHT
R
T
C
T
CIRCUIT DESCRIPTION
OSC. An external resistor in the range of
200 k
to 2 M
and an external capacitor
in the range of 0.001
µ
F to 1
µ
F determine
the frequency of the internal oscillator. The
period of oscillation is nominally R
T
C
T
with
the overall output time period (after the
digital countdown) of
t = 4064 R
T
C
T
where t is in seconds. See also MODE
SELECT.
OUTPUT. The output is an open-collector
of a Darlington-connected transistor. The
output is ON (low) during the timing period.
An external Zener diode is used to protect
the output against inductive-load switching
transients and automotive "load dump".
TOGGLE. A push-button, momentary-action
switch at this input toggles the timer from
the OFF to the ON state. The oscillator and
countdown circuitry are started on the rising
edge of the input pulse. Internal de-bounce
circuitry is included.
SUPPLY. The timer requires a supply current
applied to this pin through a current-limiting
resistor (R
S
). An internal 8 volt Zener diode
shunt regulator provides a stable supply to
the device over wide supply voltage varia-
tions. Capacitor C
S
is used to provide
decoupling.
MODE SELECT. With MODE SELECT
connected to GROUND, the first activation
will run for the preset time delay. All activa-
tions after the first will time out at half of the
initial preset time. This sequence is reset
each time the supply is interrupted. With
MODE SELECT connected to SUPPLY
(V
REG
), the timer will repeat the preset time
delay each time it is activated.
Dwg. No. ES-013
COURTESY LIGHT TIMER
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the
detail specifications as may be required to permit improvements in the design of its products.
Components made under military approvals will be in accordance with the approval requirements.
The information included herein is believed to be accurate and reliable. However, Allegro
MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other
rights of third parties which may result from its use.
PDF 
ZIP